11
Chase Playback
There are 3 ways to start chase playback: manual trigger, auto trigger or audio trigger.
1. Manual trigger
1) When the power is turned on, the unit automatically enters Manual mode, and all channel outputs are in
black-out state (the Blackout LED flashes in the display window).
2) Tap the BLACKOUT button (20) to enable the channel output. Blackout LED goes out.
3) Tap your selected CHASE button (14), its LED will be lit. Then use the FADE TIME fader (6) to adjust the
running state.
4) Tap the Up/Down button (11) to run the chase step by step.
2. Auto trigger
1) Tap the AUTO button (18), the Auto Trigger LED will light up in the display window, indicating you are
now in the Auto trigger mode.
2) Select your desired chase and press related CHASE button (14). Its LED will flash.
3) After selecting the bank of scenes to run, you can use the SPEED slider and FADE TIME slider (5+6) to
adjust the speed of the scene progression.
4) You can use the TAP Sync/Display button (19) to set the speed instead. The amount of time between the
last two taps will instruct the controller in the length of time between steps. This setting will stay in effect,
until the speed slider is moved.
5) Press the AUTO/Display button (18) to exit Auto mode. Auto Trigger LED goes out
Note: You can simultaneously run more chases as your desire. The enabled chases will be run by your
operating sequence.
3. Audio trigger
1) Tap the MUSIC/Bkc button (16). The Audio Trigger LED will light up in the display window, indicating you
are now in the Audio trigger mode.
2) Select your desired chase and press the related CHASE button (14). Its LED will flash. The chases will
run sensitively by the Audio signal through the built-in microphone).
3) MUSIC/Bkc button (16) again to exit from the Audio mode. Audio Trigger LED goes out
JOYSTICK / CHANNEL SELECTION
Set-up Joystick
1) Press and hold the PROGRAM button (15), until the LED is lit.
2) Press and hold the MODE and FINE button (7+8) at the same time, the assign LED should light. If the
reverse LED lights, press FINE and MODE (7+8) again to enter assign mode.
3) Use the BANK Up/Down buttons (11) to select the axis you wish to assign (Pan or TILT).
4) Use the "TAP/DISPLAY button (19) to select a 16 or 8 channel mode. The display will show you:
"PH:XX", "PLXX", "TH:XX" or "TL:XX". (P=Pan, T=Tilt, H=High, L=Low, "XX" is the channel number.)
5) Press the FIXTURE button (1) corresponding to the scanner you wish to assign.
6) While holding the MODE button (8), press the scene number corresponding to the slider which controls
the movement. (Example: If pan is controlled by slider number 4, press and hold the MODE button while
tapping scene button 4#). All LEDs will flash briefly.
7) When finished press the FINE and MODE buttons (7+8) at the same time again to exit Assign mode.
Reverse Joystick Movement / DMX Channel
1) Enter program Mode.
2) Press the FINE and MODE buttons (7+8) to enter assign mode, then press FINE and MODE buttons
again (7+8) to enter reverse mode. The reverse LED lights up, indicating reverse mode is active.
3) Use BANK Up/Down button (11) to change between the Pan and Tilt, the corresponding LED lights,
indicating this selection. After your settings, press and hold down the MODE button (8), and then tap the
FINE button (7) at the same time to exit.
(13 pages)
(19 pages)
(35 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals